development board

Posted on by Jean-Luc Aufranc (CNXSoft) - 1 Comment on STMicro SensorTile is a Tiny STM32 Module with Bluetooth 4.1 LE and Four Sensor Chips

STMicro SensorTile is a Tiny STM32 Module with Bluetooth 4.1 LE and Four Sensor Chips

STMicroelectronics SensorTile is a 13.5 x 13.5mm sensor board based on STM32L4 ARM Cortex-M4 microcontroller, a MEMS accelerometer, gyroscope, magnetometer, pressure sensor, a MEMS microphone, as well as a 2.4Ghz radio chip for Bluetooth 4.1 Low Energy connectivity for wearables, smart home, and IoT projects. SensorTile hardware specifications: MCU – STMicro STM32L476 ARM Cortex-M4 microcontroller@ up to 80 MHz with 128 KB RAM, 1MB flash Connectivity – Bluetooth 4.1 Smart/LE via BlueNRG-MS network processor with integrated 2.4GHz radio compliant with Sensors LSM6DSM 3D accelerometer + 3D gyroscope LSM303AGR 3D Magnetometer + 3D accelerometer LPS22HB pressure sensor/barometer MP34DT04 digital MEMS microphone I/Os – 2x 9 half holes with access to UART, SPI, SAI (Serial Audio Interface), I2C, DFSDM, USB, OTG, ADC, and GPIOs signals Debugging – SWD interface (multiplexed with GPIOs) Power Supply Range – 2V to 5.5 V Dimensions – 13.5 x 13.5 mm Software development can be done through […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 2 Comments on Nordic Semi Unveils nRF52840 Bluetooth 5 Ready SoC and Development Kit

Nordic Semi Unveils nRF52840 Bluetooth 5 Ready SoC and Development Kit

Nordic Semiconductor nRF52xx Bluetooth and 2.4 GHz solutions are very often found in development kits and low power devices such as wearables, and it’s no surprise that the company introduced a new nRF52840 SoC supporting Bluetooth 5, the new standard promising twice the range, and four times the speed of BLE 4.x, as well as ANT, 802.15.4, 2.4GHz proprietary, and NFC connectivity. Nordic Semi nRF52840 key features and specifications: MCU – 32-bit ARM Cortex-M4 @ 64 MHz with with FPU Memory & Storage – 256 KB RAM, 1MB Flash Connectivity Bluetooth 5-ready multiprotocol radio Bluetooth 5 data rate support: 2 Mbps, 1 Mbps, 500 kbps, 125 kbps 104 dB link budget for Bluetooth low energy -96 dBm sensitivity for Bluetooth low energy Programmable output power from +8 dBm to -20 dBm NFC-A tag on chip Single-ended antenna output (on-chip balun) I/Os USB – Full-speed 12 Mbps USB controller SPI up […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 8 Comments on Hardkernel ODROID-VU8C is 8″ LCD Display and Case Kit for ODROID C1+ and C2 Boards

Hardkernel ODROID-VU8C is 8″ LCD Display and Case Kit for ODROID C1+ and C2 Boards

While it’s quite easy to find displays for development boards, they do not always come with a case, so you’d have to make your own. One easier option for the Raspberry Pi boards is the official Raspberry Pi 7″ LCD touch screen Display, plus RS Premium touchscreen case that selling for $132 in total including Raspberry Pi 3 board. But Hardkernel has now launched their own ODROID-VU8C 8″ Touch Display Shell Kit compatible with ODROID-C1+ and ODROID-C2 boards. Specifications and Kit Contents: 8-inch TFT-LCD with 1024×768 resolution (4:3 ratio) 10 finger capacitive touch input Back-light brightness control with ODROID GPIO PWM Viewing angle : Left 75, Right 75, Up 75, Down 75 degree Screen Dimensions : 189 x 149 x 29 mm Viewable screen size : 162 x121.5 mm (active area) Power Supply – 5V/4A DC to power barrel (powering both the LCD and ODROID ARM Linux board) Power consumption […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 35 Comments on Firefly-RK3399 Rockchip RK3399 Development Board Launched on Kickstarter for $139 and Up

Firefly-RK3399 Rockchip RK3399 Development Board Launched on Kickstarter for $139 and Up

Firefly-RK3399 is the first, and for now the only one, development board equipped with the latest Rockchip RK3399 hexa-core Cortex A72 & A53 processor. It’s just not available yet, but the board has now been launched on Kickstarter where it is offered for $139 to $199 depending on options. Firefly-RK3399 board specifications: SoC – Rockchip RK3399 hexa-core big.LITTLE processor with dual core ARM Cortex A72 up to 2.0 GHz and quad core Cortex A53 processor with ARM Mali-T860 MP4 GPU with OpenGL 1.1 to 3.1 support, OpenVG1.1, OpenCL and DX 11 support System Memory Standard – 2 GB DDR3 Plus devkit – 4 GB DDR3 Storage Standard – 16 GB eMMC flash, micro SD card, M.2 socket Plus devkit – 32 GB eMMC flash, micro SD card, M.2 socket Video Output & Display Interfaces 1x HDMI 2.0 up to 4K @ 60 Hz 1x DisplayPort (DP) 1.2 interface up to […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 8 Comments on $59 HiFive1 Arduino Compatible Board is Powered by Sifive Open Source RISC-V MCU (Crowdfunding)

$59 HiFive1 Arduino Compatible Board is Powered by Sifive Open Source RISC-V MCU (Crowdfunding)

Royalty-free RISC-V instruction sets has been getting in the news in the last few years with various MMU designs from companies or projects like lowRISC, PULPino, and SiFive, and recently there are been rumors that Samsung may use RISC-V in their future IoT SoCs. Many projects are still in progress, and while you can get involved in OnChip Open-V MCU crowdfunding campaign to their get the MCU or a development board, the cost for the MCU ($49) and development board ($99) is a little on the high side, and delivery is expected in 2018 for most rewards. SiFive appears to have a more interesting open source RISC-V solution with HiFive1 Arduino compatible board going for $59 and slated to ship between December 2016 and February 2017. HiFive1 development board specifications: MCU – SiFive Freedom E310 (FE310) 32-bit RV32IMAC processor @ up to 320+ MHz (1.61 DMIPS/MHz) Storage – 128 Mbit […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 17 Comments on LeMaker HiKey 96Boards Board Sells for $29.70 (Promo)

LeMaker HiKey 96Boards Board Sells for $29.70 (Promo)

[Update: The promo is over back!] You’d think Cyber Monday should be over by now, but ITEAD Studio still has a clearance with real 70% discount, as 96Boards hardware compliant LeMaker Hikey board is now sold for just $29.70 instead of the usual $99 price. A quick reminder of the specifications: SoC – HiSilicon Kirin 620 octa core Cortex A53 processor @ 1.2 GHz with ARM Mali-450MP4 GPU System Memory – 2 GB LPDDR3 @ 800 MHz Storage – 8GB eMMC + micro SD slot Video Output / Display – HDMI up to 1080p, MIPI-DSI interface Connectivity – 802.11 a/b/g/n Wi-Fi, Bluetooth 4.1 LE (WL1835MOD module) USB – 2x USB 2.0 host ports, 1x micro USB OTG Camera – MIPI CSI interface Debugging – UART header), unpopulated 10-pin JTAG header (back) Expansion headers 40-pin LS (Low Speed) Expansion connector – UART, I2C, 12x GPIOs, SPI, PCM, PWM, SYS_DCIN, 1.8V, 5V, […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 3 Comments on Theobroma Announces Rockchip RK3368 and RK3399 Qseven System-on-Modules

Theobroma Announces Rockchip RK3368 and RK3399 Qseven System-on-Modules

Theobroma Systems, an embedded system company based in Austria, has designed several Allwinner systems-on-module compliant with μQseven & Qseven standards in the past. The company has now started to work with Rockchip and reached “an advanced design stage” for the development of μQseven and QSeven systems-on-module powered by RK3368 and RK3399 processors. RK3368-uQ7 module specifications: SoC – Rockchip RK3368 octa-Core ARM Cortex-A53 processor up to 1.2GHz with Imagination Technologies PowerVR G6110 GPU System Memory – up to 4GB DDR3-1600 SDRAM on-module (512MB, 1GB, 2GB (default) and 4GB configuration available) Storage – Up to 128GB eMMC flash on-module (8GB default), 16 Mbit to 128 Mbit SPI NOR flash on-module Video Capabilities –  H.264 decoding up to 2160p30, H.265 decoding up to 2160p60, video encoding up to 1080p30 Connectivity – GbE PHY on-module CAN – On-module communication offload controller for CAN 230-pin MXM edge connector with: 10/100/1000 Mbps Ethernet USB – 1x […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 8 Comments on Getting Started with Pine64 PADI IoT Stamp – Part 2: Serial Console, GCC SDK, Flashing & Debugging Code

Getting Started with Pine64 PADI IoT Stamp – Part 2: Serial Console, GCC SDK, Flashing & Debugging Code

PADI IoT Stamp module powered by Realtek RTL8710AF ARM Cortex M3 WiFi SoC is a potential competitor to Espressif ESP8266 modules.  Pine64, the manufacturer of the module, sent me their kit with a $2 IoT stamp, a breakout board, a USB to TTL debug board and a J-Link debug board. In the first part of the review I’ve shown the hardware and how to assemble PADI IoT stamp kit. In the second part I’m going to write a tutorial / getting start guide showing how to control the board with AT commands, build the firmware with GCC SDK, and finally demonstrate how to flash and debug the firmware with the J-Link debugger. The Quick Start Guide indicates you need to connect the USB to TTL debug board to UART2 instead of UART1 as I did on the very similar B&T RTL-00 RTL8710AF module, and set connection settings to 38400 8N1. […]

Exit mobile version