display News - Page 9 of 29 - CNX Software

May 23, 2023May 23, 2023 by Jean-Luc Aufranc (CNXSoft) - No Comments

FireBeetle 2 ESP32-S3 camera board ships 16MB flash, 8MB PSRAM, PCB or external antenna

DFRobot “FireBeetle 2 ESP32-S3” is a 2MP camera board with ESP32-S3N16R8 dual-core WiFi and Bluetooth microcontroller fitted with 16MB flash and 8MB PSRAM, and offered in two versions: a more compact variant with a PCB antenna, and one with an external antenna offering a better signal quality. The FireBeetle 2 ESP32-S3 also features two rows of I/Os with GPIO, I2C, SPI, ADC, USB 2.0, etc…, a USB-C port for power and programming, a few buttons, and support for a LiPo battery through a 2-pin JST connector and a charging circuit. FireBeetle 2 ESP32-S3 specifications: ESP32-S3-WROOM-1 wireless module SoC – ESP32-S3FN16R8 dual-core Tensilica LX7 microcontroller @ 240 MHz with 2.4 GHz 802.11n WiFI 4 and Bluetooth 5.0 LE connectivity Memory – 8MB PSRAM Storage – 16MB SPI flash Camera – Camera connector fitted with 2MP OV2640 camera with 68° FoV, up to 1600×1200 resolution Display – GDI connector for optional 1.54-inch, […]

May 23, 2023May 23, 2023 by Jean-Luc Aufranc (CNXSoft) - 7 Comments

Ultrawide 8.8-inch HDMI and USB information display is offered with optional touchscreen support

8.8-inch information display HDMI USB touchscreen

Last year, I wrote about the Turing Smart Screen low-cost 3.5-inch display based on a WCH CH552T 8-bit E8051 core microcontroller that connects to a PC or other device through a USB Type-C cable in order to display system or other information using AIDA64 software or an open-source Python software. I’ve just come across another display that appears to serve the same purpose, except the “GeekTeches V35” is an ultrawide 8.8-inch display with 1920×480 resolution, micro USB and micro HDMI interfaces, and optional support for a touchscreen. GeekTeches V35 specifications: Display 8.8-inch IPS display with 480×1920 resolution (21:9 aspect ratio) with optional touch screen Pixel size – 0.114 x 0.114 mm Display area – 54.72 x 218.88 mm Wide display angle Brightness – 550cd/m2, adjustable Driver: IC/LCM Driver IC Display interface – “MIPI BIT interface”. Not sure what this is… a typo for MIPI DSI? Backlight current – 160ma Backlight […]

May 21, 2023May 29, 2023 by Jean-Luc Aufranc (CNXSoft) - 6 Comments

Using BTT Pad 7 touchscreen display with Raspberry Pi CM4

The BTT Pad 7, or BIGTREETECH Pad 7 in full, is a 7-inch touchscreen display that ships with the CB1 Allwinner H616 system-on-module compatible with Raspberry Pi CM4. The display is mostly designed for 3D printers with its SPI and CAN Bus interfaces, but it can also be used as a standard tablet PC. So today, I’ll switch the CB1 with a Raspberry Pi CM4 Lite module and report my experience doing the conversion and using it as a Raspberry Pi CM4 tablet PC running Raspberry Pi OS, and test it with a 3D printer with Klipper in another post later on. Installing a Raspberry Pi CM4 (Lite) module in the BTT Pad 7 We’ll need the Pad 7, a Raspberry Pi CM4, and a few tools. The first step is to remove the red heatsink by loosening four screws with a 2.0mm hex key, as well as the cover […]

May 18, 2023May 18, 2023 by Jean-Luc Aufranc (CNXSoft) - 5 Comments

BeepBerry handheld Linux computer drives 2.7-inch display with Raspberry Pi Zero W

Good news! The PocketCHIP handheld Linux computer is back! OK, not quite but that’s what the Raspberry Pi Zero-powered BeepBerry reminds me of with a Blackberry-like keyboard, a small 2.7-inch display, and a 2,000mAh LiPo battery for power. The BeepBerry is another open-source hardware design from SQFMI, who previously did the Watchy ESP32 E-Ink smartwatch, that runs Raspberry Pi OS Lite on the Raspberry Pi Zero/Zero W, and also includes a Raspberry Pi RP2040 to handle the keyboard and peripherals. BeepBerry specifications: SBC – Raspberry Pi Zero board with a Broadcom BCM2835 ARM11 processor @ 700 MHz, VideoCore IV GPU, or Raspberry Pi Zero W with WiFi and Bluetooth Storage – MicroSD card slot Display – Ultra-low power high contrast 2.7-inch Sharp Memory LCD with 400 x 200 resolution User input – QWERTY tactile keyboard w/ backlight and touchpad based on Solder Party BB Q20 Keyboard USB – USB-C programming […]

May 17, 2023May 18, 2023 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

$25 Renesas “HMI Board” features RA6M3 microcontroller for RT-Thread & LVGL development

The Renesas HMI board is a Renesas RA6M3 Cortex-M4F development board with a 4.3-inch LCD developed in collaboration with the teams behind the RT-Thread RTOS project and LVGL open-source graphics library. Besides a color display for HMI (Human Machine Interface), the board also features a microSD card for data storage, Ethernet and WiFi connectivity, Arduino headers and PMOD connectors for expansion, a microphone and a speaker, a CAN bus terminal block, and two USB-C ports for debugging and power. Renesas HMI board specifications: MCU – Renesas RA6M3 (R7FA6M3AH3CFB) Arm Cortex-M4F microcontroller @ 120MHz with 2MB Flash, 640KB RAM, TFT controller, 2D accelerator, and JPEG decoder. Storage – MicroSD card slot Display – 4.3-inch LCD (RGB 888) Audio – Microphone and speaker Networking Low-profile 10/100M Ethernet RJ45 port RW007 SPI WiFi module by Shanghai Ruiside Electronic Technology USB – 2x USB Type-C ports Serial – 2-pin CAN bus terminal block Expansion […]

May 15, 2023 by Jean-Luc Aufranc (CNXSoft) - 4 Comments

Review of MaTouch_ESP32-S3 4-inch Display Demo Kit with sensors, Arduino, LVGL graphics library

Matouch Environmental Monitor LVGL graphics library

Makerfabs MaTouch_ESP32-S3 4-inch Display Demo Kit is an ESP32-S3 development board with a 4-inch touchscreen display, a TVOC sensor, and a thermal camera. It can be used to make various projects such as electronic photo frames. air quality monitors, or patient screening devices MaTouch_ESP32-S3 4-inch display demo kit unboxing When we unpack the box, we will find the device as in the picture, consisting of the following items: The mainboard of the MaTouch_ ESP32-S3 4-inch Display with the following specifications: Controller – ESP32-S3-WROOM-1, PCB Antenna, 16MB Flash, 8MB PSRAM, ESP32-S3-WROOM-1-N16R8 Wireless – WiFi & Bluetooth 5.0 Storage – MicroSD card slot LCD 4.0-inch IPS display with 480×480 resolution, 50+ FPS RGB 5/6/5+ SPI interface using ST7701S controller. 5 Points Touch, Capacitive via GT911 touch panel driver. Audio – MAX98357A USB – Dual USB Type-C (one for USB-to-UART and one for native USB); USB to UART Chip: CP2104 Expansion – 2x […]

May 11, 2023 by Jean-Luc Aufranc (CNXSoft) - 4 Comments

Banana Pi BPI-Centi-S3 – An ESP32-S3 board with an 1.9-inch TFT display and a rotary encoder

Banana Pi BPI-Centi-S3 ESP32-S3 display board

Banana Pi BPI-Centi-S3 is an ESP32-S3 WiFi & BLE IoT board with a 1.9-inch color TFT display, a rotary encoder, and a few I/Os, which offers an alternative to the T-Track ESP32-S3 board with AMOLED and trackball we covered a few days ago. The Banana Pi board also comes with a 2MB on-chip PSRAM, an 8MB SPI flash, a USB Type-C port for power and debugging, two buttons, a buzzer, and an RGB LED. Besides powering the board with its USB-C port, you can also connect a LiPo battery with charging support. Banana Pi BPI-Centi-S3 specifications: SoC – Espressif Systems ESP32-S3 dual-core Tensilica LX7 @ up to 240 MHz with vector instructions for AI acceleration, 512KB RAM, 2MB PSRAM, wireless connectivity Storage – 8MB SPI flash Connectivity via ESP32-S3 2.4 GHz 802.11 b/g/n Wi-Fi 4 with 40 MHz bandwidth support up to 150 Mbps Bluetooth Low Energy (BLE) 5.0 connectivity […]

May 10, 2023 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

LILYGO T-Track ESP32-S3 board combines 1.1-inch AMOLED display with trackball

After the T-Display-S3 AMOLED board, LILYGO has launched another ESP32-S3 board with an AMOLED display named the T-Track that features a smaller 1.1-inch AMOLED display and a trackball that allows the user to navigate any menu or user interface shown on the display. The rest of the board’s specifications are very similar with an ESP32-S3R8 dual-core chip with 8MB PSRAM providing WiFi and BLE connectivity, a 16MB SPI flash for storage, two rows of pins for up to 18x GPIOs, a Qwicc connector for module expansion, and support for USB-C charging and a LiPo battery for power. T-Track specifications: Wireless MCU – Espressif Systems ESP32-S3R8 dual-core Tensilica LX7 @ up to 240 MHz with vector instructions for AI acceleration, 512KB RAM, 8MB PSRAM, wireless connectivity Storage – 16MB flash Connectivity via ESP32-S3 2.4 GHz 802.11 b/g/n Wi-Fi 4 with 40 MHz bandwidth support Bluetooth Low Energy (BLE) 5.0 connectivity with […]