Linux News - Page 123 of 434 - CNX Software

June 4, 2021June 4, 2021 by Jean-Luc Aufranc (CNXSoft) - No Comments

TQ unveils i.MX 8M Plus LGA module and evaluation single board computer

We’ve seen plenty of systems-on-module based on NXP i.MX 8M Plus AI processor announced at Embedded World 2021 either with edge or board-to-board connectors. TQ TQMa8MPxL is a bit different as an i.MX 8M Plus LGA (Land Grid Array) system-on-module meant to be soldered on a carrier board. The company also took the occasion to unveil STKa8MPxL evaluation kit based on TQMa8MxML in single board computer format to demonstrate its new LGA module. TQMa8MPxL i.MX 8M Plus LGA module Specifications: SoC – NXP i.MX 8M Plus “Quad 8 ML/AI”, “Quad 6 Video”, or “Quad 4 Lite” processor with four Cortex-A53 cores, one Cortex-M7 core, Vivante GPU, video encoder/decoder, HiFi4 audio DSP, and 2.3 TOPS AI accelertor System Memory – Up to 4 GB LPDDR4 Storage – Up to 256 MB (MBytes)Quad SPI NOR flash, up to 256 GB eMMC flash, optional EEPROM up to 64 Kbit 362-pin LGA with Storage […]

June 4, 2021June 4, 2021 by Jean-Luc Aufranc (CNXSoft) - 5 Comments

reServer 2-bay multimedia NAS is equipped with an Intel Core Tiger Lake SBC

Seeed Studio has just introduced reServer dual-bay multimedia NAS based on Intel Core i3/i5/i7 Tiger Lake 11th generation processor. The networked storage device is based on ODYSSEY X86 V2 single board computer that offers an upgrade to the ODYSSEY-X86J4105 and ODYSSEY-X86J4125 Gemini Lake SBC’s. reServer comes with up to to 64GB dual-channel memory, dual 2.5GbE, support for two 3.5-inch SATA drives, HDMI and DisplayPort video output, and some USB 3.0/2.0 ports. reServer (preliminary) specifications: SoC (one or the other) Intel Core i3-1115G4 dual-core/quad-thread processor with 48 EU Intel UHD Graphics @ 400 – 1250MHz; 28W TDP Unnamed Intel Core i5 with 80 EU Intel Iris Xe Graphics G7 @ 400-1300MHz; 28W TDP Unnamed Intel Core i7 with 96 EU Intel Iris Xe Graphics G7 @ 400-1300MHz; 28W TDP Co-processor – Microchip ATSAMD21G18 32-Bit Arm Cortex-M0+ microcontroller System Memory – Up to 64GB dual-channel DDR4-3200 SDRAM via two SO-DIMM sockets Storage […]

May 31, 2021 by Jean-Luc Aufranc (CNXSoft) - No Comments

Mercury+ XU6 Xilinx Zynq UltraScale+ module is optimized for I/O-intensive applications

Enclustra, a company headquartered in Switzerland specializing in FPGA solutions, has recently announced the launch of the Mercury+ XU6 system-on-module based on Xilinx Zynq UltraScale+ MPSoC. The module is optimized for I/O-intensive applications with up to 294 user I/Os, up to eight 6/12.5 Gbps multi-gigabit transceivers, and available with six different variants of Xilinx MPSoC. The company also offers Mercury+ ST1 and PE1 baseboards for evaluation and early software development. Mercury+ XU6 SoM Key features and specifications: SoC – Xilinx Zynq Ultrascale+ MPSoC (ZU2CG, ZU2EG, ZU3EG, ZU4CG, ZU4EV, or ZU5EV) with: CPU ARM dual-/quad-core Cortex-A53 processor up to 1333 MHz ARM dual-core Cortex-R5 up to 533 MHz GPU – Mali-400MP2 GPU (only for EG/EV variants) Video Codecs – H.264 / H.265 Video Codec (only for EV variants) FPGA fabric – Up to 256,000 system logic cells System Memory – Up to 8 GB DDR4 ECC SDRAM (PS side) Storage – […]

May 27, 2021May 31, 2021 by Jean-Luc Aufranc (CNXSoft) - 8 Comments

QMiroPlus-201W – Arm router and Intel NAS in one device with Qualcomm IPQ4019 & Celeron J4125

QNAP QMiroPlus-201W is an unusual networked storage device that’s acting both as a 2.5GbE & WiFI 6 router and NAS combining Qualcomm IPQ4019 Arm SoC for the router functions, and an Intel Celeron J4125 quad-core Gemini Lake processor for the NAS functions. Usually, you’d get the choice of either an Arm or Intel processor, but here QNAP decided to use both to keep the same performance as having separate Arm-based router and Intel-based NAS, but in a much more compact form factor. QNAP QMiroPlus-201W hardware specifications: SoC/memory/internal storage For router SoC – Qualcomm IPQ4019 quad-core Arm Cortex A7 @ 716.8MHz Memory – 512MB DDR3 Internal Storage – 4MB SPI NOR Flash & 4GB eMMC flash For NAS SoC – Intel Celeron J4125 quad-core Gemini Lake processor @2.0 GHz Memory – 4GB DDR4 Internal Storage – 4GB eMMC flash Data Storage – 2x 2.5-inch SATA 3Gb/s (Compatible with 6Gb/s SSD/HDD) bay Networking […]

May 23, 2021May 23, 2021 by Jean-Luc Aufranc (CNXSoft) - 22 Comments

Rock Pi 4 Plus SBC gets Rockchip OP1 processor, eMMC flash pre-loaded with Twister OS Armbian

The low-cost Rock Pi 4 SBC was unveiled in 2018 with a Rockchip RK3399 processor, up to 4GB RAM, and Raspberry Pi 3 form factor. Rock Pi 4 Plus builds on the relatively popular single board computer with an upgrade to Rockchip OP1 processor, which is a higher performance RK3399 SoC typically used in Chromebooks and ASUS Tinker Board 2. The new board also adds 16 to 128 GB eMMC flash, instead of relying on an optional eMMC module, and will come pre-loaded with Twister OS Armbian lightweight desktop OS based upon Armbian Focal 20.04.1 LTS (aarch64) for Rockchip RK3399-based SBCs. Four variants of Rock Pi 4 Plus share most of the same specifications: SoC – Rockchip OP1 big.LITTLE hexa-core processor with 2x Arm Cortex-A72 @ up to 2.0 GHz, 4x Cortex-A53 @ up to 1.4 GHz, a Mali-T864 GPU with support OpenGL ES1.1/2.0/3.0/3.1, OpenVG1.1, OpenCL, DX11, and AFBC, and […]

May 20, 2021May 21, 2021 by Jean-Luc Aufranc (CNXSoft) - 49 Comments

Nezha RISC-V Linux SBC launched for $99 and up

Last month, we wrote about Allwinner D1 SBC & processor that promised to offer a relatively low-cost RISC-V Linux solution. We were not given a name at the time, but there was a logo of Nezha, a fictional character from Chinese literature. The board is now known as the Nezha SBC and has been launched on Indiegogo for $99 and up as a board designed for IoT projects running Linux, but can also be purchased directly on Aliexpress for the same price. [Update: It can also be purchased on Taobao for 599 RMB] Nezha SBC specifications: SoC – Allwinner D1 single-core XuanTie C906 64-bit RISC-V processor @ 1.0 GHz with HiFi4 DSP, G2D 2D graphics accelerators Memory – 1GB DDR3 memory Storage – 256MB SPI NAND flash, MicroSD card slot Video Output – HDMI 1.4 port up to 4Kp30, MIPI DSI & touch panel interface up to 1080p60 Decoding – […]

May 18, 2021 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

DSBOX-NX2 – An NVIDIA Jetson Xavier NX Industrial Fanless PC

Turkish company Forecr has launched DSBOX-NX2 NVIDIA Jetson Xavier NX based industrial fanless PC equipped with the company’s own DSBoard-NX2 carrier board and designed for “multi-stream deep learning edge analytics” and IIoT applications. The compact embedded computer comes with 8GB RAM, up to 2TB SSD storage, as well as HDMI 2.0 output, Gigabit Ethernet, two USB 3.1 ports for high resolution cameras, serial ports, and some GPIOs among other features. Forecr DSBOX-NX2 specifications: System-on-Module – NVIDIA Jetson Xavier NX module with hexa-core NVIDIA Carmel ARM v8.2 64-bit processor, NVIDIA Volta GPU with 384 CUDA core & 48 Tensor Cores, 8 GB 128-bit LPDDR4x, 16GB eMMC flash Storage – M.2 Key M SSD slot, MicroSD card slot Video Ouput – 1x HDMI 2.0 up to 3840×2160 at 60 Hz Networking Gigabit Ethernet Wireless – WiFi, Bluetooth, 4G LTE, 5G connectivity by extension sockets USB – 2x USB 3.1 Type-A Expansion 1x […]

May 13, 2021 by Jean-Luc Aufranc (CNXSoft) - No Comments

Raspberry Pi CM4 based Exo Sense Pi multi-sensor device gets optional earthquake sensor

Sfera Labs’ Exo Sense Pi is a device with multiple environmental sensors based on the 2GB version of the Raspberry Pi CM4 module designed for residential and commercial applications such as environmental monitoring and data gathering, BLE positioning, indoor people and assets tracking, rooms management and access control, voice control, and more. The Exo Sense Pi devices include optional WiFI 5 and Bluetooth 5.0 LE connectivity depending on the RPI CM4 module selected, and ships with temperature, humidity, air quality (VOC), light intensity, microphone, and PIR motion sensors by default, but there’s also an optional earthquake sensor. Exo Sense Pi specifications: SoM – Raspberry Pi CM4 (16GB eMMC flash) or CM4 Lite module with 2GB RAM by default. But obviously compatible with other models. Storage – MicroSD card socket for CM4 Lite module Wireless connectivity – 2.4 GHz, 5.0 GHz IEEE 802.11 b/g/n/ac wireless; Bluetooth 5.0, BLE depending on installed […]