Renesas releases the DA14592, a new dual-core Cortex-M33/M0+ BLE chip with integrated flash

DA14592 chip block diagram

The DA14592 System-on-Chip (Soc) is Renesas’ “lowest power consumption and smallest, multi-core Bluetooth LE device.” According to the company, this chip’s design was achieved by making careful tradeoffs between on-chip memory and die size. The chip offers an ultra-low power mode that uses only 2.3mA when transmitting radio signals at 0dBm and consumes 1.2mA to receive radio signals. It also supports a hibernation mode that uses about 90nA and can extend the operating life of battery-powered products. The active mode is best for processing-intensive products and uses 34µA for every MHz of CPU clock. Projected key applications for the DA14592 chip include crowd-sourced location (CSL) tracking as used in Apple’s Airtags, remote control units, human interface devices, asset tracking, IoT end nodes, data logging, connected health, and activity tracking. Renesas DA14592 specifications: CPU cores: Cortex-M33F running at up to 64MHz as application core Cortex-M0+ at 64MHz as configurable MAC Memory: […]

Renesas’ RX23E-B MCU offers a low-drift 24-bit A/D converter with a 125 kSPS sampling rate

Renesas' new RX23E-B MUC offers a low-drift 24-bit delta-sigma A/D converter with up to 125 kS/S Sampling Rate - That is eight times faster than its predecessor.

Renesas’ new RX23E-B MCU offers a low-drift 24-bit delta-sigma A/D converter with up to 125 kS/S Sampling Rate – That is eight times faster than its predecessor. This controller is clocked at 32-MHz and offers up to 256 KB Flash memory rail-to-rail programmable gain instrumentation amplifiers, ±10 V input pins, a low-drift voltage reference, and on-chip excitation current sources. This year Renesas introduced a range of new products including, the RZ/T2L Arm Cortex-R52 with an EtherCAT controller, and the RA4E2 and RA6E2 Arm Cortex-M33 MCUs for wearables and appliances. Renecus also released its first 32-bit RISC-V CPU  this year, you can check those out if interested. Features of Renesas’ RX23E-B MCU: CPU: 32 MHz 32-bit RXv2 core Includes FPU/DSP instructions Memory: 256 KB code Flash 8 KB data Flash 32 KB SRAM 24-bit Delta-Sigma ADC with PGA: High data rate: max 125 kSPS Ultra-low noise: 190 nVRMS at 977 SPS/gain=64 […]

Infineon launches PSoC Edge Cortex-M55/M33 microcontrollers for enhanced AI and ML applications

The PSoC Edge microcontrollers integrate the Arm Cortex-M55 core with Helium DSP and the Ethos U55 NPU unit for advanced AI tasks. It also includes a power-efficient Arm Cortex-M33 core paired with an NNLite(DSP/NPU) for simpler AI tasks.

Infineon’s new PSoC Edge series of microcontrollers integrates the Arm Cortex-M55 core with Helium DSP and the Ethos U55 NPU unit for advanced AI tasks. It also includes a power-efficient Arm Cortex-M33 core paired with an NNLite(DSP/NPU) for simpler AI tasks. This setup allows the device to be more efficient in varying load conditions. Infineon’s PSoC lineup is a configurable microcontroller powered by Arm Cortex-M4, Cortex-M3, or Cortex-M0+ cores. The main USP (Unique Selling Point) of this lineup is its configurable digital and analog components. This feature makes them somewhat similar to an FPGA, but an FPGA is far more difficult to program than these microcontrollers and they are also very power-hungry. The device is equipped with advanced HMI and “Always-on” capability. “Always-on” is a feature of this device to constantly monitors and responds to signals automatically, making it suitable for smart homes, security, wearables, robotics, and many more. Key […]

COM Express Type 6 Compact module features 14th gen Intel Core Ultra “Meteor Lake” processor

Intel Core Ultra COM Express

ADLINK cExpress-MTL is a COM Express Type 6 Compact module based on the just-announced 14th gen Intel Core Ultra “Meteor Lake” processor family with up to fourteen CPU cores in 6P+8E configuration, eight Xe-cores (128 EUs), and an NPU (11pTOPS/8.2eTOPS) in a 15 or 28W TDP thermal configuration delivering up to 1.9x the GPU performance of the previous generation (Raptor Lake). The power consumption will also be lower thanks to Intel Core Ultra’s new Low-Power E-cores that are 30 to 50% more efficient than the E-cores in 13th gen Intel Core processors, and the faster GPU and built-in NPU will enable hardware-accelerated AV1 encoding/decoding and various devices leveraging AI such as portable medical ultrasound devices, industrial automation, autonomous driving, AI robots, and more. cExpress-MTL specifications: Meteor Lake-H/U SoC (one of the other) Intel Core Ultra 7 MS3 165H 16-core (6P+8E+2LPE) processor @ 1.4 / 5.0 GHz with 24MB cache, Intel […]

M5StickC PLUS2 IoT development kit features ESP32-PICO-V3-02 SiP, larger 200 mAh battery

M5StickC Plus2 IoT development kit

M5Stack M5StickC PLUS2 is a battery-powered ESP32 IoT development kit with a 1.14-inch display, a built-in microphone, a 6-axis gyroscope and accelerometer, a few buttons, a buzzer, a Grove connector and a GPIO header for expansion. It builds upon the M5StickC Plus released in September 2020, but replaced the ESP-PICO-D4 SiP with an ESP32-PICO-V3-02 still based on ESP32 WiSoC but having 8MB SPI flash and 2MB flash and also features a larger 200 mAh battery along with a new CH9102 USB to TTL chip and does without a PMIC. M5StickC PLUS2 key features and specifications: ESP32-PICO-V3-02 SiP – Espressif Systems ESP32-PICO-V3-02 system-in-package with ESP32 dual-core WiFI and Bluetooth IoT processor @ up to 240 MHz, 8MB SPI flash, 2MB PSRAM Display – 1.14-inch Color TFT LCD with 135×240 resolution (ST7789v2 driver) Audio – SPM1423 microphone, buzzer USB – 1x USB-C port for power and programming using CH9102 USB to TTL chip […]

STMicro VD55G1 – A small, low-power global shutter I3C camera sensor for computer vision

STMicro VD55G1 global shutter camera sensor

STMicro VD55G1 is a new global shutter I3C camera sensor with a small die size of 2.7 x 2.2 mm, 804 x 704 pixels native resolution, and consuming about 1mW in its ‘always-on’ autonomous mode to wake up the host when motion is detected. Camera sensors are available with rolling or global shutter, with most from the former type, but as we’ve seen in our reviews of the e-Con Systems See3CAM_24CUG (USB 3.1) and the Raspberry Pi Global Shutter (MIPI CSI) global shutter cameras, the latter is much better we capturing moving objects clearly at high frame rates with fewer artifacts than with rolling cameras. The VD55G1 global shutter sensor will also benefit from the same advantage but is offered in a smaller package working over MIPI CSI and/or I3C, making it suitable for devices with small batteries used in applications such as eye tracking or motion estimation. STMicro VD55G1 […]

LILYGO Mini E-Paper Core IoT controller gets ESP32-S3 wireless microcontroller

LILYGO Mini E-Paper ESP32-S3

LILYGO Mini E-Paper Core has gotten an upgrade to the ESP32-S3 wireless microcontroller. The IoT controller was first introduced in 2021 with an ESP32-PICO-D4 system-in-package, a 1.02-inch E-Paper display, and a few GPIOs on the back, and the company kept the same design for the ESP32-S3 model called “Mini E-Paper Core S3”. The tiny ESP32-S3 IoT controller can still be used for integrated into your own project, and the company also provides several shields with nRF24L01 2.4GHz wireless or 433/868 MHz “LoRa” connectivity to transform the device into a longer range IoT device. Mini E-Paper Core S3 specifications Wireless SoC – Espressif Systems ESP32-S3FN4R2 CPU – Dual-core Tensilica LX7 @ up to 240 MHz with vector instructions for AI acceleration Memory – 512KB RAM, 2MB PSRAM Storage – 4MB flash Wireless – 2.4 GHz WiFi 4 and Bluetooth Storage – MicroSD card socket Display – 1.02-inch e-paper display with 128×80 […]

Adafruit Metro ESP32-S3 WiFi and Bluetooth IoT board comes in Arduino UNO form factor

ESP32-S3 Arduino UNO board

Adafruit Metro ESP32-S3 is an IoT development board with ESP32-S3 WiFi and Bluetooth wireless SoC, 8 MB PSRAM, and 16 MB Flash that follows Arduino UNO – or Adafruit Metro – form factor. The board also comes with two STEMMA QT I2C connectors for further expansion, comes with a microSD card socket for storage, a JTAG header for advanced debugging, and supports various power options with 6-12V DC via a DC jack, 5V DC via a USB-C port, and a 2-pin connector for a LiPo battery plus the board integrates charging and battery monitoring chip. Adafruit Metro ESP32-S3 specifications: Wireless module ESP32-S3-WROOM-1 MCU – ESP32-S3 dual-core LX7 microprocessor @ up to 240 MHz with Vector extension for machine learning Memory – 8MB PSRAM Storage – 16MB SPI flash Connectivity – WiFi 4 and Bluetooth 5 with LE/Mesh PCB antenna Certifications – FCC/CE certification Storage – MicroSD card slot USB – 1x […]

Exit mobile version