Raspberry Pi News - Page 26 of 154 - CNX Software

April 5, 2023 by Jean-Luc Aufranc (CNXSoft) - 6 Comments

Add Z-Wave LR (Long Range) to Raspberry Pi or Home Assistant Yellow with Zooz 800 Series USB stick or GPIO Module

Z-Wave Long Range Raspberry Pi Home Assistant Yellow

We wrote about the new Z-Wave Long Range (LR) standard aka “Z-Wave Plus LR” promising four times the range and 10-year battery life in September 2020 but hadn’t heard much about it since then, at least until now, as Zooz has launched the ZST39 LR USB Stick and ZAC93 LR GPIO module based on a Z-Wave 800 Series chip, with the GPIO module compatible with Home Assistant Yellow and Raspberry Pi SBCs. Zooz 800 Series Z-Wave Long Range GPIO Module ZAC93 LR ZAC93 LR specifications: Z-Wave Frequency – 908.42 MHz (US, CA, MX) / 921.4 MHz (AU, NZ) / 868.42 MHz (EU) Wireless Range – Up to 1 mile/1.6 km in open space with Long Range enabled (up to 300 meters in open space, up to 76 meters indoors in traditional mesh networks) Support for up to 200 devices in a single network Host interface – 10-pin header to Raspberry […]

April 4, 2023April 4, 2023 by Jean-Luc Aufranc (CNXSoft) - 5 Comments

M5Stack CM4Stack – A tiny Raspberry Pi CM4 Linux computer with an integrated 2-inch display

M5Stack CM4Stack is a tiny Arm Linux mini PC based on Raspberry Pi CM4 that measures 59 x 44 x 46mm and integrates a 2-inch touchscreen display for information and control, as well as the usual ports you’d expect from a mini PC such as HDMI, USB 3.2 ports, Gigabit Ethernet, and so on. We’ve previously written about M5Stack Core and Atom controllers based on ESP32 microcontrollers, an optional 2.0-inch display, and a few GPIOs. The company has now decided to provide a similar solution with a jump in performance and interfaces with the CM4Stack development kit. CM4Stack specifications: SoM – Raspberry Pi CM4 (CM4104032) with SoC – Broadcom BCM2711 quad-core Cortex-A72 processor @ 1.5 GHz System Memory – 4GB RAM Storage – 32GB eMMC flash Wireless module with 802.11 b/g/n/ac WiFi 5 and Bluetooth 5.0 Integrated display – 2.0-inch LCD with ST7789V2 controller, touchscreen function Video Output – HDMI […]

April 4, 2023April 9, 2023 by Jean-Luc Aufranc (CNXSoft) - 12 Comments

Raspberry Pi RP2040 pHAT board comes with a 40-pin GPIO header

0xC0FFEE’s RP2040 PHAT is both a Raspberry Pi RP2040 development board and a pHAT for Raspberry Pi and Pi Zero Linux SBCs that exposes the I/Os through the 40-pin GPIO header traditionally found in Raspberry Pi single board computers. The board comes with all features of the Raspberry Pi Pico board including a USB port for power and programming, an SPI flash, and a BOOT button, but also adds a Reset button. That means it’s software compatible, except for the user LED connected to GPIO 26, and works with the MicroPython and C SDKs, as well as the Arduino IDE, Zephyr RTOS, and more. RP2040 pHAT specifications: MCU – Raspberry Pi RP2040 dual-core Cortex-M0+ microcontroller @ 133 MHz with 264KB SRAM Storage – 128Mbit SPI flash (based on the chip in the photo above) USB – 1x USB 1.1 Type-C port used for power and programming Expansion – 40-pin Raspberry […]

April 3, 2023March 31, 2024 by Jean-Luc Aufranc (CNXSoft) - Comments Off

PiEEG shield for Raspberry Pi enables brain computer interfaces (Crowdfunding)

PiEEG is an open-source hardware Raspberry Pi shield that measures electroencephalography (EEG), electromyography (EMG), and electrocardiography (ECG) bio-signals and provides a brain-computer interface to applications or robots for gaming, entertainment, sports, health, etc… Ildar Rakhmatulin, a Research Associate at Heriot-Watt University in Edinburgh, is passionate about open-source brain-computer interfaces and first created the IronBCI project based on ADS1299 and STM32 and published a research paper entitled “Low-cost brain computer interface for everyday use” about his work. But cost increases related to the semiconductors shortage of recent years meant the price for his “low-cost” project shot up to over $1,000. So he went back to the drawing board and created the PiEEG shield for Raspberry Pi now available on Crowd Supply. PiEEG shield specifications: ADC – Texas Instruments ADS1299 Analog-to-Digital Converter for biopotential measurements Supported SBCs – Raspberry Pi 3 or 4, and boards with the same 40-pin GPIO header. Host […]

March 31, 2023March 31, 2023 by Jean-Luc Aufranc (CNXSoft) - No Comments

Metal enclosures for the Raspberry Pi Compute Module 4 IO board

Waveshare metal box for Raspberry Pi Compute Module 4 IO Board

I was informed about the “CM4 IO Computer” based on the official Raspberry Pi Compute Module 4 IO board housing in a metal enclosure along with the Raspberry Pi CM4 module. I initially thought it was new, but it’s been out at least since 2021. Nevertheless, it turns out there are at least two of this type of metal enclosures for the CM4 IO board, and when buying full systems, they may provide a way to source Raspberry Pi CM4 system-on-modules since individual modules are so hard to purchase if you are not a company with some minimum monthly production volume. As a development platform, the Raspberry Pi Compute Module 4 IO board is not optimized for cost or size, but there’s apparently enough demand that at least two companies – EDATEC and Waveshare – decided to make metal enclosures for them. EDATEC metal enclosure for the Compute Module 4 […]

March 29, 2023March 29, 2023 by Jean-Luc Aufranc (CNXSoft) - No Comments

XIAO ESP32S3 board gets some senses with a camera and microphone module, plus a round touchscreen display

Last week, we wrote about the new XIAO ESP32S3, a tiny ESP32-S3 board from Seeed Studio. The company has now launched the XIAO ESP32S3 Sense adding a camera and microphone module connected through a board-to-board connector, as well as the Round Display for XIAO that can help people easily create wearable devices with a touchscreen based on any board from the XIAO family. XIAO ESP32S3 Sense XIAO ESP32S2 Sense specifications: Wireless MCU – Espressif Systems ESP32-S3R8 dual-core Tensilica LX7 microcontroller @ 240 MHz with 512KB SRAM, 8MB PSRAM, Wi-Fi 4 & Bluetooth 5.0 dual-mode (Classic + BLE) connectivity Storage – 8MB SPI flash, microSD card slot Antenna – External u.FL antenna USB – USB Type-C port for power and programming Camera – OV2640 camera sensor up to 1600×1200 resolution Audio – Built-in digital microphone Expansion I/Os 2x 7-pin headers with 1x UART, 1x I2C, 1x SPI, 11x GPIO (PWM), 9x […]

March 28, 2023 by Jean-Luc Aufranc (CNXSoft) - 5 Comments

Convert your 3D printer into a metal cutting machine with an Electrical Discharge Machining kit (Crowdfunding)

Rack Robotics’ Powercore is an Electrical Discharge Machining (EDM) kit that converts your existing 3D printer (or CNC router) into a machine capable of cutting high-precision and detailed metal parts. We’ve already seen 2-in-1 3D printers and laser engravers such as the Creality Ender 3 S1 Pro, but while this type of machine can usually cut plywood or engrave stainless steel, the laser is not powerful enough to cut through aluminum. The Powercore EDM kit changes that by enabling the cutting of aluminum parts up to 4mm thick, although aluminum sheets that are 1mm or thinner are recommended. But before we get into Powercore details, what is Electrical Discharge Machining exactly? Engineers Edge explains: Electrical Discharge Machining, EDM is one of the most accurate manufacturing processes available for creating complex or simple shapes and geometries within parts and assemblies. EDM works by eroding material in the path of electrical discharges […]

March 28, 2023March 29, 2023 by Jean-Luc Aufranc (CNXSoft) - 5 Comments

Servo and motor control with Raspberry Pi Pico, CircuitPython, and Wukong 2040 breakout board

Raspberry Pi Pico Wukong 2040 Motor Control CircuitPython

ELECFREAKS Wukong 2040 is a multifunctional breakout board designed for Raspberry Pi Pico. It is equipped with interfaces for four DC motors, up to twelve servos, a buzzer, A\B buttons, RGB “rainbow” lights, a Reset button, etc… The board can be powered by a single 18650 3.7V LiPo battery and integrates a power management IC that monitors the battery level and can also charge the battery via a USB charger. Battery life is typically 60 minutes per charge but can last over 120 minutes depending on the load. Wukong 2040 key features and specifications Description of the Wukong 2040 interfaces Specifications and dimensions of the Wukong 2040 Expansion Board for Raspberry Pi Pico The Wukong 2040 breakout board for the Raspberry Pi Pico can control up to four DC motors and up to 12 servo motors as shown in the diagram below. Pinout diagram of the Wukong 2040 board […]