Reviews - Page 52 of 120 - CNX Software

December 3, 2018April 13, 2021 by Jean-Luc Aufranc (CNXSoft) - 6 Comments

Xiaomi Mi A2 Review – Part 1: Unboxing, Firmware Update, Antutu

I’ve been using Xiaomi Mi A1 smartphone for well over a year, and during my initial review I was quite satisfied with the phone, and over time I was also pleased to receive regular firmware updates (monthly), and even an update to Android 8.0 and 8.1. Eventually, I found out the camera would be work that well in all situation as you can see from photos in that post, and a few months ago, I broken the display during a cycling trip, and eventually the phone basically died after one year due to an issue with the eMMC flash that become unbearably slow. I intend to use it at least for 18 months, since we can expect firmware update during that time frame. But it was not meant to be, and I was due for a new phone. Xiaomi Mi A2 / A2 Lite smartphones were launched in August, and […]

December 2, 2018April 13, 2021 by Jean-Luc Aufranc (CNXSoft) - 7 Comments

Particle Mesh Networking Review – Part 2: Getting Started Guide with Argon & Xenon

Particle Mesh Network Argon Xenon Success

I’ve recently received a Particle Mesh IoT Development Kit with one Argon WiFi + Mesh (802.15.4) board acting as gateway, three Xenon Mesh boards, and various sensors and accessories. I’ve already showcased the hardware in the first part in the review, so in this post I’ll post my experience getting started with Particle Mesh networking using the kit. Beside the kit, you’ll need a few micro USB cables, a mobile phone running Android or iOS, a reliable Internet connection (more on that later), and a host PC for programming and debugging potential issues. Setting Up Particle Argon & Xenon boards First we’ll need to configure / setup the boards. Go to https://setup.particle.io to login or create an account if you don’t already have one, and you should be brought the following page. Select Mesh, and you’ll be asked to setup a gateway first. Any of the boards from Particle Mesh […]

November 13, 2018January 15, 2022 by Jean-Luc Aufranc (CNXSoft) - 8 Comments

Khadas Edge Developer Package Review – Part 1: Unboxing, Captain and Edge-IO Expansion Boards

Shenzhen Wesion recently launched an Indiegogo campaign for their Rockchip RK3399/RK3399Pro based Khadas Edge, Edge-1S and Captain boards. The Edge boards have an interesting form factor as they are both standalone boards, and system-on-modules compatible with Captain carrier board, and the smaller Edge-IO board. While the crowdfunding campaign is on-going, the company decided to send me an early version of Khadas Edge Developer Package for evaluation. I’ll start out by checking out the content of the kit, and show how to get started with assembly, before reviewing the board with Linux at a later date. Khadas Edge Developer Package Unboxing I received the developer kit in a blank carton board package, but they’ll likely have a prettier package at launch like they did for heir VIM2 board. Anyway, the important part is the content. From top left to bottom right: An IR remote control, the package for the Edge board […]

November 3, 2018August 6, 2021 by Jean-Luc Aufranc (CNXSoft) - 6 Comments

Particle Mesh IoT Development Kit Review – Part 1: Unboxing

Back in February of this year, Particle introduced three low cost IoT development boards based on Nordic Semi nRF52840 wireless chip supporting “Particle Mesh” networking based on the 802.15.4 radio in the chip and OpenThread implementation of Thread IoT communication protocol. The company recently announced they were now shipping the kits pre-ordered earlier this year, and released two IoT development tools based on Node-RED and Visual Studio Code. Particle contacted me as well as to find out whether I was interested in reviewing their latest WiFi / Bluetooth / Mesh kit, and I’ve just received the bundle, which comes with a bunch of items, so I decided to write an unboxing post first to have a first look at the hardware, before playing with it in one or two weeks. Particle Mesh IoT Development Kit Bundle Unboxing That’s what I got from UPS… From top left to bottom right: The […]

October 15, 2018October 24, 2018 by Ian W MORRISON (Linuxium) - 5 Comments

TopJoy Falcon Review – A Windows 10 Mini Laptop (Prototype)

The Topjoy Falcon is a mini laptop reminiscent of netbooks and similar to the recent GPD Pocket 2 or One Mix Yoga devices. Marketed as an 8 inch (203mm) pocket-sized computer with the following specification: Intel Pentium Silver N5000 CPU 8G RAM 256G SSD disk 1920*1200 FHD IPS touch screen 6000 mAh battery for up to 8 hours working time 1 x USB A 3.0, 1 x USB Type-C 1 x 3.5mm headphone jack 1 x Mini HDMI port Active cooling 802.11ac WiFi, Bluetooth 4.0 Backlit keyboard Windows 10 Home Weight 550g (1lb 3oz) Fits easily in your pocket Although you would need a large pocket as whilst It is physically small consisting of an approximately 8″ by 5.2” and about 0.7” thick (203mm x 132mm x 18mm) when closed it is in reality too big for the average pocket. It will soon be available on Kickstarter with an early bird price of $399 and an expected retail price of […]

October 11, 2018 by Ian W MORRISON (Linuxium) - 11 Comments

Beelink X55 Review – Part 2, Take 2: New Drivers and BIOS

When I reviewed the Beelink X55 earlier, I encountered poor graphics performance when testing the device with its ‘Out-Of-The-Box’ configuration. As a quick reminder the Beelink X55 is a NUC-style mini PC powered with an Intel Pentium Silver J5005 processor and comes with a 128GB mSATA SSD with pre-installed Windows 10 Home together with 8GB DDR4 RAM (soldered and is non-expandable) and space plus a connector for an SSD. In an attempt to address the poor graphics performance I reinstalled Windows using Microsoft’s ISO however I then found I had missing drivers: Having contacted Beelink through the support email enclosed with the device they replied with a link to a full driver pack. So having downloaded and unzipped the file I updated the first driver: followed by the second: resulting in additional entries to the Intel Dynamic Platform and Thermal Framework (DPTF). Having fixed the driver issue I then reran […]

October 5, 2018October 11, 2018 by Ian W MORRISON (Linuxium) - 10 Comments

Beelink X55 Review – An Intel Gemini Lake mini PC Tested with Windows 10 and Linux

The Beelink X55 is very similar in style to Intel’s NUC7PJYH NUC reviewed earlier except that it is not a kit but a fully functional Windows mini PC. It is physically small consisting of an approximately 4.5″ by 4” case about 1¾” tall with a front panel that includes the power button and a couple of USB ports and a headphone jack with the rest of the ports including two HDMI (2.0) ones at the rear: The specifications include: The key highlights are that the Beelink X55 comes a 128GB mSATA SSD with pre-installed Windows 10 Home together with 8GB DDR4 RAM (soldered and is non-expandable) and space plus a connector for an SSD. Starting with a quick look at the hardware information shows it is mostly aligned to the specification but see the note below about the memory: As usual I ran my standard set of benchmarking tools to […]

October 3, 2018June 19, 2019 by Karl Johnson - 2 Comments

Genmitsu CNC Router Review – Part 1.5: Laser Attachment

Hey Karl here with a small update for the SainSmart Genmitsu CNC Router 3018 review. In the first part I described the build and first cuts. And in this part I am calling it 1.5 because it is to just talk about the optional laser attachment that was just made available and initial impressions. In the first part I commented about the laser connector on the board. The stars aligned and Sainsmart asked if we wanted to check out their 2.5W PWM controlled laser sold for $89.99 with free shipping. Installation In the box all you get is the laser itself and some eye protection. At first I wanted to mount the laser on the side of the tool head so it would be easy to change between CNC and the laser. I took the laser apart and was going to use the 2 mounting holes and ended up breaking […]