Processors Category - Page 643 of 1195 - CNX Software

June 20, 2018 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

Semtech SX1261/SX1262 LoRa Development Kit Now Available for $305

Semtech announced SX1261, SX1262 and SX1268 LoRa chips in January as updates to their current LoRa solutions with a lower footprint, better efficiency, and even longer range. Mass production and development kits were expected in March 2018, and today I found out Semtech SX1261/SX1262 development kit is sold on Mouser for $305. The SX126xDVK1CAS kit comes with the following items: 2x SX126xMB1xAS RF modules including an ST Nucleo Mbed board and a touchscreen 2x Mini-USB / USB connection cables 2x 868/915MHz antennas 2x Mini-USB cables 2x touchscreen styluses Read-Me Note The SX1261/SX1262 LoRa Transceivers offer continuous frequency coverage from 150MHz to 960MHz. You’ll find information to get started in the user guide. Basically, the two boards will show a menu on the touchscreen with radio test modes, settings and utilities (e.g. firmware update) as well as two demos: DEMO Ping Pong performs a bidirectional range test between the two radio […]

June 20, 2018June 20, 2018 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

Raspberry Pi 3 and Movidius Neural Compute Stick to the Rescue Against Child Pornography

Warning note: While there won’t be any NSFW photos in this post, there will be some photos of ladies in light clothing (e.g. bikini) and “naked” animals for testing purpose… Intel released Movidius Neural Compute Stick allowing low power image recognition at the edge earlier this year, and we’ve seen it work just fine with Raspberry Pi 3 board delivering three times the performance against an inference solution leveraging VideoCore IV GPU. Christian Haschek owns a photo hosting site (PictShare) which happens to run open source code with the same name, and allows user to upload images anonymously. However, he soon found out that at least one user uploaded some child pornography. He contacted the authorities, but then wondered whether there may be others? Since there are simply too many photo on the website to look it up manually, he decided to look for a solution, and went with a […]

June 19, 2018June 19, 2018 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

Onenuts 4G LTE TV Box Comes with Optional Battery and Zigbee Connectivity

In some countries, especially in the Middle Easy and Africa, 4G LTE is a popular way of getting broadband Internet, and in the past we covered several 4G LTE TV boxes running Android such as WeTek Hyperion, SDMC DV8230-AP LTE, or Geniatech ATV329. Shenzhen Tomato now offers another options with their “Onenuts 4G-LTE Android OTT Set-Top Box” powered by Amlogic S905X processor, and that happens to come with a compartment for optional batteries. Onenuts 4G LTE TV box specifications: SoC – Amlogic S905X quad core Arm Cortex-A53 processor @ 1.5 GHz with penta-core Mali-450 GPU System Memory – 1GB or 2GB Storage – 8GB, 16G, or 32G eMMC flash; micro SD card slot Video Output – HDMI 2.0a up to 4K UHD @ 60 Hz, AV output (composite) Audio – Video – 10-bit H.265 & VP9 Profile 2 4K @ 60fps, H.264 4K @ 30fps, AVS+ & H.264 1080p60 Connectivity […]

June 19, 2018June 19, 2018 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

$10 H801 WiFi RGB LED Controller Supports Sonoff-Tasmota Open Source Firmware

This week-end, I played with ANAVI Light Controller, an open source hardware solution based on ESP8266 used control 12V RGB LED strips. The board has the advantage of being open source with KiCad schematics, Arduino firmware, and HTML5 server program available, so easy to get started and modify the features as you see fit, and it also supports external I2C sensors via three headers. That’s a low volume project made in Eastern Europe and as a result the board costs $25, so I was shortly made aware there were cheaper solution, and if you are ready to mess around a little bit, H801 WiFi controller appears to be one of the most interesting solution as it sells for under $10 shipped on Aliexpress or eBay, and is officially supported by Sonoff-Tasmota open source firmware. H801 specifications: Connectivity – 802.11 b/g/n WiFi (2.4GHz) with about 10 meter range Output – 5x […]

June 19, 2018June 19, 2018 by Jean-Luc Aufranc (CNXSoft) - 29 Comments

ODROID-GO is an Arduino Compatible, ESP32 based Portable Gaming Console Kit

When I first saw Hardkernel made ODROID-GO portable gaming console, I immediately thought they did a Linux device ala PocketCHIP, since so far the company has only designed Android & Linux development board. But ODROID-GO game console is actually based on Espressif ESP32 WiSoC, programmable with the Arduino IDE, and launched to celebrate Hardkernel’s 10-year anniversary. ODROID-GO specifications: SoC – Custom ESP32-WROVER module with ESP32 SoC @ up to 240 MHz, 16 MB Flash, and 4MP PSRAM Storage – micro SD card slot connected via SPI Display – 2.4″ 320×240 TFT LCD (SPI) Connectivity – WiFi 802.11 b/g/n 2.4GHz – 2.5GHz, Bluetooth 4.2 BR/EDR, BLE Speaker – 0.5Watt 8Ω Mono USB – 1x micro USB port for charging (500mA) and USB-UART communication Expansion Port – 10-pin header with I2C, GPIO, IRQ at 3.3Volt Misc – Buttons: Menu, Volume, Select, Start, A, B, Direction Pad Battery – 3.7V/1,200mAh Li-Polymer good for […]

June 18, 2018June 18, 2018 by Jean-Luc Aufranc (CNXSoft) - No Comments

Three Add-on Boards for UP Board and UP Squared – UP-AUDIO HAT, UP-CAMERA HAT, UP-POE HAT

AAEON has announced three add-on boards for their Intel based UP board (Cherry Trail) and UP Squared board (Apollo Lake): UP-AUDIO HAT – Features external ports for a microphone and speakers/headphones UP-CAMERA HAT – Comes with two FPC/FFC connectors for 2M security camera UP-POE HAT – Adds WAN and LAN Gigabit Ethernet ports and PoE support UP-AUDIO HAT AAEON’s UP-Audio HAT currently only works with UP board, and features the following: Audio Codec – Realtek ALC5672 3.5mm Audio Jacks – 1x Line out, 1x MIC Headers – 2x speaker Built-in Components – 2x digital microphones, 1x buzzer Connects to board via 40-pin GPIO female header Dimensions – 85 mm x 56 mm The board is supported in Windows 10, Android 6, and Ubuntu 16.04. UP-CAMERA HAT The camera board works with UP Board, UP Squared and UP Core boards. UP-CAMERA HAT specifications & features: 2x MIPI CSI-2/ DSI DPHY Re-timer […]

June 18, 2018December 28, 2018 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

ALLDOCUBE KNote5 Gemini Lake Tablet Runs Windows 10 on a 11.6″ Display

Intel Gemini Lake processors have already been seen in several mini PCs such as Intel June Canyon NUCs, as well as some laptops from Acer, Jumper, and others, but ALLDOBUCE brings us what looks to be the first Gemini Lake tablet with KNote5 model equipped with a Intel Celeron N4100 processor, 4GB RAM, 128 GB storage, and a 11.6″ display. ALLDOCUBE KNote5 specifications: SoC – Intel Celeron N4100 quad core Gemini Lake processor @ 1.10 GHz / 2.40 GHz (Boost) with Intel UHD graphics 600 ; 6W TDP System Memory – 4 GB LPDDR4 Storage – 128 GB internal storage (SSD?), micro SD card slot up to 128 GB Display – 11.6″ FHD (1920×1080) IPS display with 10-point capacitive touchscreen Audio – Dual speaker, microphone, 3.5mm audio jack Connectivity – Dual band 802.11 b/g/n/ac WiFi and Bluetooth 4.0 USB – 1x USB type C port Camera – 2.0MP front-facing camera […]

June 17, 2018November 16, 2020 by Jean-Luc Aufranc (CNXSoft) - 7 Comments

ESP8266 RGB LED Strip Control with ANAVI Light Controller, Arduino, MQTT, and HTML5

Anavi-Light-Controller-Starter-Kit-Assembly

A few months ago I reviewed ANAVI Light pHat for Raspberry Pi which allows you to control an LED RGB strip from the popular development board. However, if all you need is to switch the RGB LED light on and off, or change the color, the hardware is clearly overpowered for the tasks. So Leon ANAVI designed another board based on ESP8266 – ANAVI Light Controller – which does the same thing with lower cost and more power efficient hardware. Leon sent me a sample for review, so let’s see what we’ve got. ANAVI Light Controller Starter Kit Unboxing I received a package for the Starter kit that’s offered for $39 on CrowdSupply. We’ve got the main board, a USB debugging, an acrylic enclosure with screws and spacers, a one meter RGB LED strip, and some stickers inside the package. If we have a close look at the board we […]