ble News - Page 28 of 54 - CNX Software

October 4, 2021October 4, 2021 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

Sofabaton X1 – IR, WiFi & Bluetooth remote control supports over 500k devices (Crowdfunding)

The Sofabaton X1 remote control system aims to replace all your other remote controls in your house thanks to infrared, WiFi and Bluetooth connectivity implemented through the X1 Hub, plus an integrated 2-inch on the remote itself for configuration and device selection. The company claims that over 500,000 devices are supported including TVs, DVD & Blu-Ray players, set-top boxes, gaming consoles, etc…, and voice commands are also supported through Google Home and Amazon Alexa voice services. SofabatonX1 specifications: X1 Hub Connectivity 2.4 GHz 802.11b/g/n Wi-Fi 4 Bluetooth 5.0 LE & Bluetooth 3.0 Infrared – 10 kHz to 100 kHz Power Supply – 5V/2A via USB Type-C port Material – PMMA X1 Remote Connectivity – Not mentioned… Display – 2-inch display with clickable scroll wheel User input – D-Pad, Backlit volume, trick modes, 4x customizable buttons, etc… Battery – 1,050 mAh LiPo battery good for about 2 months on a charge […]

September 30, 2021September 30, 2021 by Jean-Luc Aufranc (CNXSoft) - No Comments

M5Stack TOUGH – A weatherproof ESP32 Industrial IoT controller

M5Stack TOUGH weatherproof ESP32 display

M5Stack has launched several ESP32 WiFi & BLuetooth IoT controllers with an integrated display such as M5Stack Core2. The latest model, M5Stack TOUGH, is a little different as it is rugged and waterproof/weatherproof with a UV resistant enclosure sealed with o-ring, and offering waterproof M12 connectors. With protection against solid objects, dust, sand, dirt, and water drops, as well as variety of installation options such as screw mount, rolled strip, magnetic and adhesive back, the M5Stack TOUGH is suitable for more demanding environments from kitchens to factory floors, and outdoor data acquisition. M5Stack TOUGH specifications: SoC – Espressif ESP32-D0WDQ6-V3 dual-core processor @ 240 MHz with 520 KB, 2.4 GHz WiFi, and dual-mode Bluetooth Extra RAM – 8MB PSRAM Storage – 16MB Flash, MicroSD card slot up to 16GB Display – 2-inch color LCD with multi-touch capacitive screen, 320×240 resolution, 853nit brightness; ILI9342C display driver and CHSC6540 chip Audio – NS4168 […]

September 29, 2021 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

Nicla Sense ME – Arduino PRO meets Bosch SensorTech’s motion and environmental sensors

Arduino is going full steam ahead with its Arduino PRO family of boards for industrial applications. After the announcement of the Portenta H7 Lite board earlier this month, the company has now introduced the Arduino Nicla Sense ME designed in collaboration with Bosch Sensortec. The Nicla Sense ME (Motion & Environment) board comes with a range of Bosch Sensortec sensors notably a 9DoF smart motion sensor and a 4DoF environmental sensor with AI capabilities, and targets industrial IoT applications either for research projects, rapid prototyping, or commercial products. Arduino Nicla Sense ME specifications: MCU – Nordic Semi nRF52832 Cortex-M4 microcontroller @ 64 MHz with 512KB Flash, 64KB RAM, Bluetooth 4.2/5.0 LE connectivity (via U-blox ANNA B112 module) Storage – 2MB SPI flash for storage; 2MB QSPI dedicated for BHI260AP Sensors BHI260AP motion sensor system with integrated AI, “Fuser 2” 32-bit Synopsys DesignWare ARC EM4 core with RISC FPU BMM150 magnetometer […]

September 23, 2021February 27, 2023 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

DIY Spotify Box features custom-designed Allwinner V3s SBC

The Spotify Box is a small DIY device based on an Allwinner V3s single-core Cortex-A7 camera SoC and a wooden enclosure designed to play Spotify songs, and not much else… The device serves as a bridge between the official Spotify app and your home audio system connected through the RCA jacks of the box. and allowing you to connect your smartphone to your audio setup and stream music throughout your house. Spotify Box specifications: SoC – Allwinner V3s single-core Cortex-A7 processor @ 1.2 GHz with on-chip 64MB DDR2 Storage – MicroSD card slot for OS Audio – 2x RCA jack for left and right audio Connectivity 10/100M Ethernet RJ45 port 2.4 GHz 802.11b/g/n WiFi 4 and Bluetooth 4.2 via RTL8723DS module Misc – Push button, RGB LED Power Supply – 5V via USB-C port Evan Hailey selected Allwinner V3s over other processors such as NXP i.MX233 or Microchip SAM9N because […]

September 9, 2021September 15, 2021 by Jean-Luc Aufranc (CNXSoft) - No Comments

LILYGO T-32C3 – A small ESP32-C3 WiFi & BLE IoT module with 4MB flash

We’re slowly starting to see more hardware-based on ESP32-C3 RISC-V processor, and LILYGO T-32C3 is a compact module based on the WiFi & Bluetooth LE processor that includes 4MB flash and a PCB antenna. I’d expect T-32C3 to be eventually found in the company’s smartwatches and development boards, and it joins other ESP32-C3 modules from AI Thinker. LILYGO T-32C3 module specifications: SoC – Espressif ESP32-C3 RISC-V processor @ 160 MHz with 400 KB SRAM, 384 KB ROM, 8KB RTC SRAM, 2.4 GHz WiFi 4, Bluetooth 5.0 LE & Mesh Storage – 4MB flash On-board PCB antenna I/Os – 22x castellated holes with GPIO, 3x ADC, SPI, UART, I2C, Boot, Reset, 5V, 3.3V, GND Dimensions – 23 x 11 x 3.5 mm (4-layer PCB) Note the USB interface is not listed in the specs, but USB DN and DP signals are located on GPIO18 and GPIO19 so USB should also be […]

September 8, 2021September 8, 2021 by Jean-Luc Aufranc (CNXSoft) - 4 Comments

25-key ESP32 Touch Matrix makes good use of ESP32’s touch sensor interface

Besides the addition of Bluetooth, there are many differences between ESP8266 and ESP32 and one of the lesser-known interfaces may be ESP32’s touch sensor interface. India-based Electro Point’s ESP32 Touch Matrix makes good use of the touch sensor interface with 25 touch pads arranged in a 5×5 matrix creating a wireless keypad that could connect over WiFi or Bluetooth to a host. ESP32 Touch Matrix board specifications: Wireless module – ESP32-WROOM-32U with Espressif ESP32-D0WD dual-core Tensilica processor, 32Mbit SPI flash, 2.4 GHz WiFi, and Bluetooth LE connectivity 25 keys arranged in a 5×5 matrix Expansion – 4-pin I2C header for expansion, e.g. an OLED display Programming – Programming headers Misc – RGB status indicator, EN button Power Supply – 5V input via 2-pin header; built-in 3.3v regulator for ESP32 Dimensions – TBD When a capacitive load, such as a human hand) is in close proximity to the sense-pad, the sensor […]

September 3, 2021October 8, 2021 by Jean-Luc Aufranc (CNXSoft) - 11 Comments

M5Stamp Pico ESP32-PICO-D4 module ships with a heat-resistant plastic shell

Most WiFi IoT modules are designed to be integrated into products with an enclosure, but the M5Stamp Pico module based on ESP32-PICO-D4 SiP comes with a removable heat-resistant plastic shell that protects the 3D antenna and components, while leaving space to solder headers and/or a Grove connector. The tiny module also comes with a button and RGB LED, and like other ESP32-based M5Stack hardware, M5Stamp Pico is programmable with UIFlow graphical programming platform and compatible with Arduino, MicroPython, and the ESP-IDF. M5Stamp Pico specifications: System-in-Package – Espressif Systems ESP32-PICO-D4 SiP with dual-core processor @ 240MHz, 520KB SRAM, 4MB flash, and 2.4 GHz Wi-Fi 4 up to 150 Mbps and Bluetooth 4.2 BR/LE connectivity Antenna – 2.4 GHz 3D antenna I/Os – 2.54mm pitch header with ADC, DAC, touch sensor, SD/SDIO/MMC host controller, SPI, SDIO/SPI slave controller, EMAC, PWM, UART, I2C, I2S, IR remote controller, up to 12x GPIO, pulse counter […]

August 24, 2021August 24, 2021 by Jean-Luc Aufranc (CNXSoft) - 6 Comments

An ESP32-based BBC Micro:bit clone – Meet Mbits

A few years ago, we noted a BBC Micro:bit clone based on ESP32 WiSoC with Banana Pi ‘s BPI:bit board with an array of 25 RGB LEDs and WiFi & Bluetooth LE connectivity. There’s now another such clone with Elecrow Mbits designed in a way that resembles the BBC Micro:bit v2 board, but replacing the Nordic Semi nRF52833 2.4GHz/BLE SoC with the ESP32 dual-core wireless chip with support for both WiFi and BLE. The specifications between Elecrow Mbits and BBC Micro:bit v2 are close enough, although ESP32 is a more powerful processor, and the MBits board comes with more memory and storage. Power consumption of the BBC Micro:bit v2 should be much better, so if anything needs to run on battery for an extended period of time, it may be a better choice, or you’re gonna need a bigger battery. The GPIO pinout looks different too, so not all Micro:bit […]